Setup Netgear Router As A Repeater: Easy Guide

Setup Netgear router as a repeater, as the name shows, it helps the users to repeat or extend the signal that comes from a router. Many people use a repeater to extend the range of their networks. Besides, it helps to enhance the signal intensity and allows the devices to connect to the network even when they are out of range. There are some devices mainly designed to extend the range of a wireless network, at the same time users can also configure it as a repeater.

Though, not every Netgear routers possibly support wireless division system, which later becomes a significant element while setting up the router as a repeater. Therefore, we suggest you go through the rules on how to setup Netgear router as a repeater provided in this article to assure you can set it up implementing these methods. The wireless repeater is generally a subset of what a broadcast access point does.

In case you are located in a large area with only a single WiFi network, then you can make use of a second router to avoid any error. Following the steps in this article, you will be able to set up your additional router to run as a repeater. Besides, it will help you to increase your router signal.

Know How to Setup Netgear Router as a Repeater

Though there are multiple approaches to setup your router as a repeater, we are going to provide you with some easy steps so that you can use your router as a repeater in a no time. Therefore, to begin with, you can follow the steps right below. Since not all router support to work as a repeater, still, you can recycle your old router to give it a try.

Step 1: Get your Router’s IP Address

To setup Netgear router as a repeater, you should first grasp a few information about your router. So, we recommend you to look for some details regarding your router. You need to check your channel type along with your security type. For that, you can move to the Control Panel and tap on the Network option.

If you are using a Windows XP device, then you need to tap on the Network Connection option then you can proceed to check the Status. After that, locate the “Support” option, and you will get to see your network setup from there.

For Vista, Windows 7, 8, and above Operating System users, they can move to the Network and Sharing section. Then, you need to select “Change Adapter Settings” and proceed with the preferred network connection. Then, move to the Status part and then check your router’s information from there.

Now, the appearing window will lead you to your device’s IP address. Write down all the details you get from there and move to the next step.

Step 2: Connect to the Router

After that, you need to go to your browser and type your system’s IP address. Next, tap the Enter button, and a setup screen for your router will appear. Then, you have to provide your username along with your password. So, provide this information and move to the next process.

Step 3: Check your WiFi Settings

Now that you are successfully connected to your router network, you need to check your WiFi settings. In the settings, you can get a customized set of your own. Note that you don’t have to reconfigure your router, you just need to have a look at its settings. So, you should get all the details from here and proceed to the next step.

Step 4: Reset your Router to the Factory Settings

To setup Netgear router as a repeater, you also need to reset your router to its factory configuration. So, locate a tiny hole at the rear of your router device to reset your router. We recommend you to use a paper-clip for resetting your router.

Step 5: Configure your Second Router

Now, it is the time to configure your second router. For that, you need to plug your network cable to your router device. Next, need to power off your primary router for a moment at the time of setting up the second router. Next, proceed with the configuration part.

Step 6: Copy Over the Settings

Next, we suggest you move to the WiFi settings page. Now, you need to enable your wireless connection, and with this, you can change your network name as well. Next, you will be able to match your security type for the password you are using on your primary router.

Step 7: Set a Fixed IP Address

Now, to setup Netgear router as a repeater, you need to run your secondary router along with your primary router with the same fixed IP address. This helps the primary router to identify the IP address and operate with the secondary router.

Then, you can move to the LAN setup page and provide the second router with the same range of IP address as the one given to the primary router. You need to prevent your secondary router to spread the IP addresses to other devices. Make the primary router manage this work.

After that, you have to disable the DHCP process. For that, you consider unchecking the DHCP option. Now, you can allocate an established IP address to your secondary router. Next, on the configuration page, you need to save the changes that you made so far. Click on the Save button to retain the changes.

Step 8: Connect it Altogether

After going through all these steps, you can now connect the devices altogether. You can prefer to connect the two routers with a single network cable. Besides, you can utilize a powerline networking adapter as well.

Step 9: Use Custom Firmware

If your router doesn’t have the WDS in it, you can choose another alternative as well. So, we recommend you install custom firmware. You can consider installing replacements such as DD and WRT.

Therefore, after implementing all these steps, you will be able to setup Netgear router as a repeater.